- 您现在的位置：买卖IC网 > Sheet目录624 > FSBB20CH60C (Fairchild Semiconductor)MODULE MOTION-SPM 600V SPM27-CC
+5 V +15 V
(19) V B(W )
VB
P (27)
Gating WH
R S
C PS
C BS
C BSC
(18) V CC(H)
(17) IN (WH)
(20) V S(W )
VCC
COM
IN
OUT
VS
W (26)
(15) V B(V)
VB
Gating VH
R S
C PS
C BS
C BSC
(14) V CC(H)
(13) IN (VH)
(16) V S(V)
VCC
COM
IN
OUT
VS
V (25)
M
M
C
U
Gating UH
R S
C PS
R F
C BS
C BSC
(11) V B(U)
(10) V CC(H)
(9) IN (UH)
(12) V S(U)
VB
VCC
COM
IN
OUT
VS
U (24)
C DCS
Vdc
R PF
C SC
(8) C SC
C(SC)
OUT(WL)
Fault
Gating WL
Gating VL
R S
R S
R S
R S
C FOD
(7) C FOD
(6) V FO
(5) IN (WL)
(4) IN (VL)
(3) IN (UL)
C(FOD)
VFO
IN(WL) OUT(VL)
IN(VL)
N W (23)
N V (22)
R SW
R SV
Gating UL
(2) COM
IN(UL)
C BPF
C PS C PS C PS
C PF
(1) V CC(L)
COM
VCC
OUT(UL)
V SL
N U (21)
R SU
C SP15
C SPC15
Input Signal for
Short-Circuit Protection
W-Phase Current
V-Phase Current
U-Phase Current
R FW
R FV
R FU
C FW
C FV
C FU
Figure 13. Typical Application Circuit
4th Notes:
1. To avoid malfunction, the wiring of each input should be as short as possible (less than 2 - 3cm).
2. By virtue of integrating an application-specific type of HVIC inside the Motion SPM ? 3 product, direct coupling to MCU terminals without any optocoupler or transformer isola-
tion is possible.
3. V FO output is open-collector type. This signal line should be pulled up to the positive side of the 5 V power supply with approximately 4.7 k ? resistance (please refer to
Figure11).
4. C SP15 of around seven times larger than bootstrap capacitor C BS is recommended.
5. V FO output pulse width should be determined by connecting an external capacitor (C FOD ) between C FOD (pin 7) and COM (pin 2). (Example: if C FOD = 33 nF, then t FO = 1.8 ms
(typ.)) Please refer to the 2nd note 5 for calculation method.
6. Input signal is active-HIGH type. There is a 5 k ? resistor inside the IC to pull down each input signal line to GND. RC coupling circuits should be used to prevent input signal
oscillation. R S C PS time constant should be selected in the range 50 ~ 150 ns . C PS should not be less than 1 nF ( recommended R S = 100 ? , C PS = 1 nF).
7. To prevent errors of the protection function, the wiring around R F and C SC should be as short as possible.
8. In the short-circuit protection circuit, please select the R F C SC time constant in the range 1.5 ~ 2.0 ? s.
9. Each capacitor should be mounted as close to the pins of the Motion SPM 3 product as possible.
10. To prevent surge destruction, the wiring between the smoothing capacitor and the P & GND pins should be as short as possible. The use of a high-frequency non-inductive
capacitor of around 0.1 ~ 0.22 ? F between the P & GND pins is recommended.
11. Relays are used in almost every systems of electrical equipment in home appliances. In these cases, there should be sufficient distance between the MCU and the relays.
12. C SPC15 should be over 1 ? F and mounted as close to the pins of the Motion SPM 3 product as possible.
?2008 Fairchild Semiconductor Corporation
FSBB20CH60C Rev. C3
13
www.fairchildsemi.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
FSBB20CH60SL
MODULE SPM 600V 20A SPM27-CA
FSBB30CH60F
IC SMART PWR MODULE SPM27-EA
FSBF10CH60BTL
MODULE SPM 600V 10A 3PH SPM27-JB
FSBF10CH60BT
MODULE SPM 600V 10A 3PH SPM27-JA
FSBF10CH60B
MODULE SPM 600V 10A 3PH SPM27-JA
FSBF15CH60BTH
MODULE SPM MOTION CTRL SPM27-JC
FSBF3CH60B
MODULE SPM 600V 3A 3PH SPM27-JA
FSBF5CH60B
MODULE SPM 600V 5A 3PH SPM27-JA
相关代理商/技术参数
FSBB20CH60CL
功能描述:IGBT 模块 20A, Motion-SPM
RoHS:否 制造商:Infineon Technologies 产品:IGBT Silicon Modules 配置:Dual 集电极—发射极最大电压 VCEO:600 V 集电极—射极饱和电压:1.95 V 在25 C的连续集电极电流:230 A 栅极—射极漏泄电流:400 nA 功率耗散:445 W 最大工作温度:+ 125 C 封装 / 箱体:34MM 封装:
FSBB20CH60CT
功能描述:IGBT 模块 600V 20A SPM
RoHS:否 制造商:Infineon Technologies 产品:IGBT Silicon Modules 配置:Dual 集电极—发射极最大电压 VCEO:600 V 集电极—射极饱和电压:1.95 V 在25 C的连续集电极电流:230 A 栅极—射极漏泄电流:400 nA 功率耗散:445 W 最大工作温度:+ 125 C 封装 / 箱体:34MM 封装:
FSBB20CH60CTSL
制造商:Fairchild Semiconductor Corporation 功能描述:
FSBB20CH60F
功能描述:IGBT 模块 HIGH VOLTAGE
RoHS:否 制造商:Infineon Technologies 产品:IGBT Silicon Modules 配置:Dual 集电极—发射极最大电压 VCEO:600 V 集电极—射极饱和电压:1.95 V 在25 C的连续集电极电流:230 A 栅极—射极漏泄电流:400 nA 功率耗散:445 W 最大工作温度:+ 125 C 封装 / 箱体:34MM 封装:
FSBB20CH60F
制造商:Fairchild Semiconductor Corporation 功能描述:SMART POWER MODULE ((NW)) 制造商:Fairchild Semiconductor Corporation 功能描述:SMART POWER MODULE, 3-PH, 600V, 20A PCB MOUNT
FSBB20CH60L
功能描述:IGBT 模块 Smart Power Module RoHS:否 制造商:Infineon Technologies 产品:IGBT Silicon Modules 配置:Dual 集电极—发射极最大电压 VCEO:600 V 集电极—射极饱和电压:1.95 V 在25 C的连续集电极电流:230 A 栅极—射极漏泄电流:400 nA 功率耗散:445 W 最大工作温度:+ 125 C 封装 / 箱体:34MM 封装:
FSBB20CH60SL
功能描述:IGBT 模块 600V/20A Smart Power
RoHS:否 制造商:Infineon Technologies 产品:IGBT Silicon Modules 配置:Dual 集电极—发射极最大电压 VCEO:600 V 集电极—射极饱和电压:1.95 V 在25 C的连续集电极电流:230 A 栅极—射极漏泄电流:400 nA 功率耗散:445 W 最大工作温度:+ 125 C 封装 / 箱体:34MM 封装:
FSBB3
制造商:MMD 制造商全称:MMD Components 功能描述:HC-49/US Surface Mounted Crystal